Put a hold tagon the shipmentand informpurchasingimmediatelyReliabilityEveryoneInvolvedNever beDestroyedData thatshows theEffectivenessof the ActionTakenEveryoneFinding TypicalCharacteristicsof the lotEnsure thatproceduresandprocesses arefollowedCheck the toolwith a 2.00 inchgauge block tomake sure it isstill set properlyAfrequencyChartCustomerAs early aspossible inthe designprocessUse allavailableinformationresourcesMIcrometerNumberofdefectsExplodedandBasicRequireAdditionalInspectionToleranceAsdictated byCompanyStandardsThe datethe tool isdue forcalibrationAs early aspossible inthe designprocessValidatedandApprovedStandards andSpecificationsforConformanceand Results ofthe inspectionSomeoneoutside oftheorganizationThat theinformationis accurateCalibratedTorqueWrenchNo, themeasuredpart exceedsthe upperlimitContinuousimprovementpolicies andproceduresQuality andcapabilityofproductionEstablishmeasurementsfor processimprovementsCalibratedUsed as aReferenceSurfaceProblemanalysistoolsAs early aspossible inthe designprocessPut a hold tagon the shipmentand informpurchasingimmediatelyReliabilityEveryoneInvolvedNever beDestroyedData thatshows theEffectivenessof the ActionTakenEveryoneFinding TypicalCharacteristicsof the lotEnsure thatproceduresandprocesses arefollowedCheck the toolwith a 2.00 inchgauge block tomake sure it isstill set properlyAfrequencyChartCustomerAs early aspossible inthe designprocessUse allavailableinformationresourcesMIcrometerNumberofdefectsExplodedandBasicRequireAdditionalInspectionToleranceAsdictated byCompanyStandardsThe datethe tool isdue forcalibrationAs early aspossible inthe designprocessValidatedandApprovedStandards andSpecificationsforConformanceand Results ofthe inspectionSomeoneoutside oftheorganizationThat theinformationis accurateCalibratedTorqueWrenchNo, themeasuredpart exceedsthe upperlimitContinuousimprovementpolicies andproceduresQuality andcapabilityofproductionEstablishmeasurementsfor processimprovementsCalibratedUsed as aReferenceSurfaceProblemanalysistoolsAs early aspossible inthe designprocess

Quality 1-34 - Call List

(Print) Use this randomly generated list as your call list when playing the game. There is no need to say the BINGO column name. Place some kind of mark (like an X, a checkmark, a dot, tally mark, etc) on each cell as you announce it, to keep track. You can also cut out each item, place them in a bag and pull words from the bag.


1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
  1. Put a hold tag on the shipment and inform purchasing immediately
  2. Reliability
  3. Everyone Involved
  4. Never be Destroyed
  5. Data that shows the Effectiveness of the Action Taken
  6. Everyone
  7. Finding Typical Characteristics of the lot
  8. Ensure that proceduresand processes are followed
  9. Check the tool with a 2.00 inch gauge block to make sure it is still set properly
  10. A frequency Chart
  11. Customer
  12. As early as possible in the design process
  13. Use all available information resources
  14. MIcrometer
  15. Number of defects
  16. Exploded and Basic
  17. Require Additional Inspection
  18. Tolerance
  19. As dictated by Company Standards
  20. The date the tool is due for calibration
  21. As early as possible in the design process
  22. Validated and Approved
  23. Standards and Specifications for Conformance and Results of the inspection
  24. Someone outside of the organization
  25. That the information is accurate
  26. Calibrated Torque Wrench
  27. No, the measured part exceeds the upper limit
  28. Continuous improvement policies and procedures
  29. Quality and capability of production
  30. Establish measurements for process improvements
  31. Calibrated
  32. Used as a Reference Surface
  33. Problem analysis tools
  34. As early as possible in the design process